Charger Orion Pennant 37

Timely recharging of the battery can significantly extend the battery life. Modern chargers are relatively inexpensive, and thanks to the presence of an automatic charging mode in almost all models, you can not worry about the timely disconnection of the device. One of the simplest and most universal memories is Orion Pennant 37.

Device Overview

The design of the Orion Pennant 37 charger is pretty simple. The product consists of a plastic case, in which there are ventilation holes for air circulation. The following display and adjustment elements are located on the front panel of the device:

• LCD display.
• Voltage switch.
• Current regulator.

The segment LCD display allows real-time control of the level of charging current and voltage. Using the knob located on the right side of the device, you can precisely set the current strength, and thanks to the presence of a three-position switch, the voltage supplied to the battery terminals is set. Depending on the type of rechargeable battery as well as on the operating mode of the device, you can set the voltage value to 14.1 V, 14.8 V or 16 V.

1. The LCD display on which: Voltage, Current, Charge time, Percentage of charge, The given amount of A / h, Warnings about an overheat or a polarity reversal.
2. Three position charge mode switch:
   14.1 V. For 12 volt AGM, GEL, EFB, traction, boat and Deep Cycle batteries.
   14.8 V. For 12 volt WET batteries (all those with liquid electrolyte).
   16 V. To charge 12 volt batteries in manual mode (recommended only for experts).
3. Regulator of amperage.

On the opposite side of the charger, Orion Pennant 37 has a fairly capacious compartment where the wires that connect to the battery and the power cord are placed. The power cable is equipped with a universal plug, and the conductors connected to the battery are equipped with convenient crocodile clips.

Specifications of the device Pennant 37

In order for the device to last as long as possible, it is necessary to know its main technical characteristics. The manufacturer in the instructions for the memory of this model indicates the following parameters:

In the process of charging the battery, voltage deviation from the nominal values ​​to the lower side is possible. The current strength almost always corresponds to the specified parameters with an error of not more than 0.2 A.

Features of the device and for which battery is intended

The features that distinguish this memory model from other similar devices include the presence of a digital display. Unlike dial gauges, the accuracy of measuring the charging current and voltage of Orion Vympel 37 is tenths. In addition to the main parameters, information on overheating and polarity reversal of the device can be displayed on the screen.

You can also use the charger of this model as a high-precision digital voltmeter. In order to measure the voltage, it is enough to connect the clamps, observing the polarity to the battery or other direct current source with a voltage of 8.5 - 23 V, while the device must be disconnected from the 220 V.

An important feature of this model is the built-in micro-fan. Such an element can significantly increase the life of the charger, because many parts of the electrical circuit that are sensitive to heat are forced to blow air immediately after a significant load appears in the electrical circuit.

The Orion Pennant 37 charger allows you to adjust the level of the charging current in a very wide range, so it can be used for any car battery. The device is ideally suited for restoring the charge of both conventional WET batteries and for batteries manufactured using such modern technologies as: AGM, EFB, VRLA.

The charger of this model is also suitable for restoring gel batteries, but only on condition that the minimum possible voltage is selected when setting up the device.

Designations of the displayed information on the screen

The presence of a digital display in the Orion Vympel 37 model allows you to display much more useful information about the charge parameters and device settings. Depending on the operating mode, the following information may be displayed on the screen:

• Model number and firmware version.
• Voltage and current during battery charging.
• Voltage and current when setting the operating mode of the device.
• Voltage and current after the battery is fully charged in automatic mode.
• Time and percentage of charge.
• Overheating device.
• Polarity reversal.
• Errors that have occurred.

Instructions with all designations can be downloaded a little lower in the appropriate section.

When setting up the device, as well as depending on the mode of its operation or the onset of certain adverse conditions, the display can select both static information and constantly changing. For example, during operation in automatic charging mode, the device will alternately display information about the various characteristics of the electricity supplied to the battery terminals.

At the time of inclusion, it will show only information about the model number and the firmware version of the device. In case of critical moments in the operation of the device, the display will blink until the adverse conditions are completely eliminated.

How to charge the battery using Pennant 37

Charging batteries using the Vympel 37 charger is possible both in automatic mode and in non-automatic mode. The main difference in the use of the device is its initial configuration.

In automatic mode

In automatic mode, the batteries are charged as follows:

• Connect the device to 220 V.
• Set the voltage selector to the position recommended for the specific battery model.
• Set the required current value using the controller located on the front panel.
• Unplug the device.
• Connect the charger wires to the battery terminals observing the polarity.
• Turn on the memory in the network.

The battery will be charged with current with predetermined characteristics. As soon as the battery is charged, the device will automatically be put into mode with the generation of the minimum value of the charging current.

In non-automatic mode

To activate the non-automatic operating mode of the charger, you will need to perform the same sequence of actions as when charging in automatic mode. The only difference is that when setting the voltage, it is necessary to switch the switch to the maximum voltage supply mode (16 V).

The current strength is selected depending on the battery capacity and should be equal to 10% of the battery capacity. That is, if the capacity is 60 A / h, then the current should be 6 amperes. It should also be remembered that a device operating in non-automatic mode must be disconnected on its own when the battery is fully charged.

Download the official PDF manual

Instructions for using the Orion Pennant 37 charger can be downloaded HERE. The manual also describes all errors and indications that may appear on the display.

You have a charger Pennant 37? Then tell us in the comments which one and about your impressions about him, this will greatly help other motorists and will make the material more complete and accurate.

 Reviews

Alexander, Moscow.

The Orion Pennant 37 Charger can be used for a variety of purposes., for example, charge batteries, connect electrical appliances operating on 12 V, and also make accurate voltage measurements.

Ruslan Angarsk.

The charger has fully met expectations. The device does an excellent job even with charging a powerful deep cycle battery.

Nazar, Kuznetsk.

Very reliable unit, there is protection against overheating and polarity reversal. It has been working for over a year without complaints. I recommend!